仪器网

欢迎您: 免费注册 仪器双拼网址:www.yiqi.com
首页-资讯-资料-产品-求购-招标-品牌-展会-行业应用-社区-供应商手机版
官方微信
仪器网-专业分析仪器,检测仪器平台,实验室仪器设备交易网 产品导购
VIP企业会员服务升级
仪器/ 产品中心/ 物性测试仪器/ 测厚仪/ 其它测厚仪/ 金属覆盖层厚度测试仪
收藏  

金属覆盖层厚度测试仪

为您推荐
详细介绍

BR-UL-MCT Metallic Coating Thickness Test System
Implementation of standards: UL 1703-20015, ASTM B499-2009, ISO 2178-1995

The test for corrosive atmosphere Test, include salt spray test and moist carbon dioxide / sulphur dioxide, measure the thicknees of coating on Zinc-coated (galvanized) Iron or steel articles. Recommend ASTM B499 and ISO 2178 Nonmagnetic coatings on magnetic basis metals measurement of coating method. UL 1703-2008 use mass loss method (chemical method), Maneuverability is not strong, and chemical reagent may pollute the environment.


The method for determining the thickness of a zinc or cadmium coating mentioned in 14.1 and 14.2 is described in following.
The solution to be used for the metallic coating thickness test is to be made from distilled water and is to contain 200g/L of reagent (or better) grade chromium trioxide (CrO3) and 50g/l of reagent (or better) grade concentrated sulfuric acid (H2SO4). The latter is equivalent to 27ml/l of reagent grade concentrated sulphuric acid, specific gravity 1.84, containing 96 percent of H2SO4.
The test solution is to be contained in a glass vessel such as a separatory funnel with the outlet equipped with a stopcock and a capillary tube of approximately 0.64 mm inside bore and 150mm long. The lower end of the capillary tube is to be tapered to form a tip, the drops from which are about 0.05 milliliter each. To preserve an effectively constant level, a small glass tube is to be inserted in the top of the funnel through a rubber stopper and its position is to be adjusted so that when the stopcock is open, the rate of dropping is 100±5 drops/min. If desired, an additional stopcock may be used in place of the glass tube to control the rate of dropping.
The sample and the test solution are to be kept in the test room long enough to acquire the temperature of the room, which 首ld be noted and recorded. The test is to be conducted at a room temperature of 21.2°C~32.0°C.
The sample is to be thoroughly cleaned before testing. All grease, lacquer, paint, or other nonmetallic coatings, including skin oils, are to be removed completely by means of solvents. The sample is then to be thoroughly rinsed in water and dried with clean cheesecloth.
The sample to be tested is to be supported from 17mm to 25mm below the orifice. The surface to be tested shall be inclined at approximately 45 degrees from the horizontal so that the drops of solution strike the point to be tested and run off quickly.
The stopcock is to be opened and the time in seconds is to be measured until the dropping solution dissolves the protective metal coating, exposing the base metal. The end point is the first appearance of the base metal recognizable by the change in color at that point.
The sample of a test lot is to be subjected to the test at three or more points, excluding cut, stenciled, and threaded surfaces, on the inside surface and at an equal number of points on the outside surface, at places where the metal coating may be expected to be the thinnest. (On enclosures made from precoated sheets, the external corners that are subjected to the greatest deformation are likely to have thin coatings.)
To calculate the thickness of the coating being tested, select from following the thickness factor appropriate for the temperature at which the test was conducted and multiply by the time in seconds required to expose base metal as noted in 38.7.

Temp.Thickness factorsTemp.Thickness factorsTemp.Thickness factors
Cadmium platingsZinc platingsCadmium platingsZinc platingsCadmium platingsZinc platings
21.11.3310.98025.01.4051.04228.91.4801.100
21.71.3400.99025.61.4161.05029.41.4901.110
22.21.3521.00026.11.4271.06030.01.5011.120
22.81.3621.01026.71.4381.07030.61.5131.130
23.31.3721.01527.21.4501.08031.11.5241.141
23.91.3831.02527.81.4601.08531.71.5341.150
24.41.3951.03328.31.4701.09532.21.5461.160


产品直通车
X您尚未登录
账号登录
X您尚未登录
手机动态密码登录
X您尚未登录
扫码登录
在线留言
官方微信

仪器网微信服务号

扫码获取最新信息


仪器网官方订阅号

扫码获取最新信息

在线客服

咨询客服

在线客服
工作日:  9:00-18:00
联系客服 企业专属客服
电话客服:  400-822-6768
工作日:  9:00-18:00
订阅商机

仪采招微信公众号

采购信息一键获取海量商机轻松掌控