Test principle: the static volumetric method, gas adsorption;
Measuring range: surface area ≥ 0.005M2/g, no upper limit; pore size 0.35-500nm; pore volume 0.0001 cm3/g, no upper limit.
Sorption gas: N2 (high purity); Ar, Kr, CO2, CH4, etc. available
Analysis No: 2 samples tested alternately
Sample Type: powders, granules, fibers, flakes and other materials
Pressure Sensor: 1000torr (133kpa), 10torr (1.33kpa); 1torr (0.133kpa) or 0.1torr (0.0133kpa); pressureaccuracy ≤± 0.15%(P.S)
P0 tube: there is a separate P0 tube in every analysis port, two in all, controlled by a separate pressure sensor, completely separates from the analysis bit, real-time detecting the nitrogen saturation vapor pressure, and participating in the theoretical calculation; also the atmospheric input method to determinate the P0 accurately;
Cold trap tube: sample degassing system has a special cold trap device that can effectively remove the water, hazardous substances and other impurities, degassed from the special sample, and it can avoid the contamination of the vacuum system;
Degassing system: two samples can be analyzed simultaneously, also can be degassed in the original port; another with two separate sample degassing station, which is independent and separate from the sample analysis. Throughout the degassing system, there are two independent heating packages, two independent temperature control systems, which can be programmed by temperature control; you can choose another four external vacuum degassing pretreatment system;
Degassing temperature: room temperature -400℃, accuracy ± 1℃;
Test Efficiency: multi-point BET surface area--30 minutes per sample; Determination micro pore size distribution from adsorption and desorptionisotherms_5-20h per sample.
Nitrogen Partial Pressure: P/Po 1×10-8 _ 0.998, the minimum resolvablerelative pressure 5 × 10-7
Ultimate vacuum:≤ 10P-6 Pa (7.5×10-9 torr)
Measurement Accuracy: ≤±1.0%(surface area); ≤0.01nm(the most frequency micro pore) ≤±0.04% (True density);≤±1.5% (STSA)
Operation Mode: Automatic
测试原理:静态容量法,低温氮吸附(或其他吸附气体);
测试精度:≤± 1.0%(比表面);≤0.02nm(最可几孔径);
测试气体:氮、氧、氢、氩、氪、二氧化碳、甲烷等 ;
测试范围:0.0005(m2/g)--至无上限(比表面积);2nm-500nm(介孔及大孔分析);0.35nm-2nm(微
孔分析);孔体积0.0001cm3/g-至无上限;
测试效率:比表面积平均每样30min;介孔、大孔分析平均每样4-6小时;微孔分析平均每样
10-15小时;
分 析 站: 独立微孔分析站,2个测试位可同时进行同位脱气预处理;
杜 瓦 瓶:每个分析位原配单独的3L真空玻璃内胆杜瓦瓶,共2个;
试原理:静态容量法,低温氮吸附(或其他吸附气体)
- 产品分类
- 品牌分类
- BET比表面仪
- 孔隙度分析仪
- 比表面积仪
- 比表面及孔径分析仪
- 孔隙度分析测试仪
- 沥青物理特性专用测试仪
- 教学仪器
- 全自动真密度仪
- 固体(粉末)表面分析仪
- 孔径/隙度分析仪
- 化工行业专用
- 比表面仪、比表面积、比表面及孔结构分析仪
- 化学吸附仪、物理吸附仪、物理/化学吸附仪
- 比表面积测定仪
- 比表面积测试仪
- 比表面积分析仪
- 比表面测试仪
- 比表面测定仪
- 比表面分析仪
- 比表面及孔径分布测定仪
- 比表面及孔隙率测试仪
- 孔径分析仪
- 孔隙率测定仪
- 孔隙度测试仪
- 孔隙度测定仪
- 孔容积测试仪
- 微孔孔径分析仪
- 比表面仪
- 动态比表面测定仪
- 氮吸附仪
- 低温物理吸附仪
- 静态容量法比表面及孔径分析仪
- 高压吸附仪
- 物理测试仪
- 粉体表面特性测定仪
- 压汞仪
- 催化剂孔结构测定仪
- 炭黑外表面测定仪
- 超细粉体表面特性分析仪
- 化工产品物性分析仪
- 新材料物性分析仪
- 颗粒物性测定仪
- 微孔分析仪
- 毛细流动法膜孔分析仪
-
仪企号北京精微高博科学技术有限公司
-
友情链接