有关实验台的技术要求翻译

itaophv57734 2010-11-25 16:53:40 521 浏览

全钢实验台台面：12.7mm厚实芯理化板台面（外延做加厚处理），耐强酸强碱耐腐蚀，耐高温（140℃）。柜体：以钢板为主体材料焊接成为试验台柜体的主要支撑结构。柜体采用1.0mm厚优质冷... 全钢实验台台面：12.7mm厚实芯理化板台面（外延做加厚处理），耐强酸强碱耐腐蚀，耐高温（140℃）。柜体：以钢板为主体材料焊接成为试验台柜体的主要支撑结构。柜体采用1.0mm厚优质冷轧钢板，框架采用1.0mm厚优质冷轧钢板。单门柜、单门单抽柜、双门柜及双门双抽柜内有一层活动隔板，以便放置器材等物。隔板采用0.8mm厚优质冷轧钢板，可承受载荷为150㎏/㎡。吊柜底板：整片设计，辅以双层中空式结构。在方便柜体清理的同时亦保持了良好的外观。产品组合后台面可承受300㎏/㎡的荷重。钢板表面处理为酸洗磷化后喷塑。地脚：钢制可调地脚，调整范围>30mm. 水盆：水盆为实验室专用聚丙烯（PP）水盆。水龙头：水龙头为化学实验室专用三口单冷龙头，材质为铜质烤漆。全木实验台台面：12.7mm厚实芯理化板台面（加厚边处理），耐强酸碱耐腐蚀，耐高温140℃ 柜体：18mm厚优质三聚氢胺成型板，2mm厚防水封边处理。上抽下门柜门有一层活动隔板。抽屉：滑轨为三节承重滑轨。拉手：为不锈钢亚光拉手（规格为96mm）。封边：2mm厚PVC高温热压封边。水盆：水盆为化学实验室专用聚丙烯（PP）水盆。水龙头：水龙头为化学实验室专用三口单冷龙头，材质为铜质烤漆。展开

参与评论

登录后参与评论

全部评论(3条)

赧晗玥1986 2012-08-01 00:00:00

mark~

赞(15)

回复(0)

评论

评论
登录后参与评论
货理中心 2012-04-24 00:00:00

Steel laboratory bench : table: 12.7mm thick core chemical board table (make thicker epitaxial processing)， resistant to strong acid and alkali resistant， high temperature (140 ℃). Cabinet: a welded steel plate as the main material to become a major test bed enclosure support structure. Cabinet with 1.0mm thick cold rolled steel plate， frame 1.0mm thick cold rolled steel plate used. Single door cabinet， single door single drawers， double door cabinet and two-door cabinet with a layer of double-pumping activities of partitions， in order to place the equipment and other items. Partitions using 0.8mm thick cold rolled steel， can withstand loads of 150 kg / ㎡. 吊柜 floor: the entire piece design， combined with double-layer hollow structure. Clean-up at a convenient cabinet also maintained a good appearance. Portfolio after the table can withstand 300 kg / m of the load. Steel surface treatment after acid phosphate spray. Feet: steel adjustable feet， adjust the range of> 30mm . basin: the basin for the laboratory-specific polypropylene (PP) basin. Faucet: faucet for the chemical laboratory dedicated three single cold faucet， made of copper paint. All wooden bench : table: 12.7mm thick core chemical board table (thick edge treatment)， resistant to acid corrosion resistance， high temperature 140 ℃ cabinet: 18mm thick high-quality melamine molding plates， 2mm thick waterproof edge treatment. Next door on the door with a layer of pumping activity of the bulkhead. Drawer: load-bearing slide rails for the three sections. Handle: matt stainless steel handle (size 96mm). Edge: 2mm thick PVC edge high temperature hot. Basin: basin of water for chemical laboratory dedicated polypropylene (PP) basin. Faucet: faucet for the chemical laboratory dedicated three single cold faucet， made of copper paint.

赞(16)

回复(0)

评论

评论
登录后参与评论
sgs54321 2010-11-26 00:00:00

Steel laboratory bench table: 12.7mm thick core chemical board table (make thicker epitaxial processing)， resistant to strong acid and alkali resistant， high temperature (140 ℃). Cabinet: a welded steel plate as the main material to become a major test bed enclosure support structure. Cabinet with 1.0mm thick cold rolled steel plate， frame 1.0mm thick cold rolled steel plate used. Single door cabinet， single door single drawers， double door cabinet and two-door cabinet with a layer of double-pumping activities of partitions， in order to place the equipment and other items. Partitions using 0.8mm thick cold rolled steel， can withstand loads of 150 kg / ㎡. 吊柜 floor: the entire piece design， combined with double-layer hollow structure. Clean-up at a convenient cabinet also maintained a good appearance. Portfolio after the table can withstand 300 kg / m of the load. Steel surface treatment after acid phosphate spray. Feet: steel adjustable feet， adjust the range of> 30mm . basin: the basin for the laboratory-specific polypropylene (PP) basin. Faucet: faucet for the chemical laboratory dedicated three single cold faucet， made of copper paint. All wooden bench table: 12.7mm thick core chemical board table (thick edge treatment)， resistant to acid corrosion resistance， high temperature 140 ℃ cabinet: 18mm thick high-quality melamine molding plates， 2mm thick waterproof edge treatment. Next door on the door with a layer of pumping activity of the bulkhead. Drawer: load-bearing slide rails for the three sections. Handle: matt stainless steel handle (size 96mm). Edge: 2mm thick PVC edge high temperature hot. Basin: basin of water for chemical laboratory dedicated polypropylene (PP) basin. Faucet: faucet for the chemical laboratory dedicated three single cold faucet， made of copper paint. 这样的行不行啊，看看嘞

赞(4)

回复(0)

评论

评论
登录后参与评论

登录或新用户注册

微信登录
密码登录
短信登录

请用手机微信扫描下方二维码
快速登录或注册新账号

微信扫码，手机电脑联动

注册登录即表示同意《仪器网服务条款》和《隐私协议》

热门问答

有关实验台的技术要求翻译: 全钢实验台台面：12.7mm厚实芯理化板台面（外延做加厚处理），耐强酸强碱耐腐蚀，耐高温（140℃）。柜体：以钢板为主体材料焊接成为试验台柜体的主要支撑结构。柜体采用1.0mm厚优质冷... 全钢实验台台面：12.7mm厚实芯理化板台面（外延做加厚处理），耐强酸强碱耐腐蚀，耐高温（140℃）。柜体：以钢板为主体材料焊接成为试验台柜体的主要支撑结构。柜体采用1.0mm厚优质冷轧钢板，框架采用1.0mm厚优质冷轧钢板。单门柜、单门单抽柜、双门柜及双门双抽柜内有一层活动隔板，以便放置器材等物。隔板采用0.8mm厚优质冷轧钢板，可承受载荷为150㎏/㎡。吊柜底板：整片设计，辅以双层中空式结构。在方便柜体清理的同时亦保持了良好的外观。产品组合后台面可承受300㎏/㎡的荷重。钢板表面处理为酸洗磷化后喷塑。地脚：钢制可调地脚，调整范围>30mm. 水盆：水盆为实验室专用聚丙烯（PP）水盆。水龙头：水龙头为化学实验室专用三口单冷龙头，材质为铜质烤漆。全木实验台台面：12.7mm厚实芯理化板台面（加厚边处理），耐强酸碱耐腐蚀，耐高温140℃ 柜体：18mm厚优质三聚氢胺成型板，2mm厚防水封边处理。上抽下门柜门有一层活动隔板。抽屉：滑轨为三节承重滑轨。拉手：为不锈钢亚光拉手（规格为96mm）。封边：2mm厚PVC高温热压封边。水盆：水盆为化学实验室专用聚丙烯（PP）水盆。水龙头：水龙头为化学实验室专用三口单冷龙头，材质为铜质烤漆。展开

电子产品实验台有什么要求啊: 请问各位大侠电子产品实验台有什么要求谢谢... 请问各位大侠电子产品实验台有什么要求谢谢展开

电磁流量计的技术要求:

平板硫化机的技术要求

平板硫化机在生产的过程中有哪些技术要求，需要符合哪些规定？《GB/T 25155-2010 平板硫化机》中就有关于平板硫化机的明确规定。

☆关于液压系统的技术要求

对于任一种液压平板硫化机来讲，动力液压缸都是极重要的部件。

-当工作液达到工作压力时，保压 1 h，液压系统的压力降：

（1）合模力大于 2.5 MN 的平板硫化机，压力降不应大于工作压力的 10%；

（2）模力不大于 2.5 MN 的平板硫化机，压力降不应大于工作压力的 15%。

当液压系统的压力降超过规定值时，液压系统应有自动补压至工作压力的功能。

液压系统应进行 1.25 倍工作压力的耐压试验，保压 5 min，不应有外渗漏。

☆关于热板的技术要求

-热板应能达到的Z高温度：蒸汽加热为 180℃，油加热、电加热为 200℃。

-热板工作员的表面粗糙度：

（1）用于带模具硫化制品的平板硫化机，Ra≤ 3.2μm；

（2）用于不带模具硫化制品的平板硫化机，Ra≤ 1.6μm。

-热板开启和闭合速度：

（1）硫化胶板、胶带的平板硫化机不应低于 6 ㎜/s；

（2）橡胶塑料发泡的平板硫化机，开模速度不应低于 160 mm/s；

（3）其他的平板硫化机不应低于 12 mm/s。

☆关于加热系统的技术要求

加热系统应进行Z高工作压力的试验，保压 30 min，不应有渗漏：

（1）蒸汽加热系统应进行蒸汽试验；

（2）油加热系统应进行热油试验。

☆关于温控装置的技术要求

平板硫化机应装有自动调温装置，在温度达到稳定状态时，调温误差不应大于±1.5%。

2019-05-29 13:06:14 620 0

翻译protocol（有关质粒DNA提取，碱裂解法）？: 请哪位高人帮忙找道这篇的中文：PreparationofPlasmidDNAbyAlkalineLysiswithSDS:Minipreparation（题）或者帮忙翻译一下，要求不要用电脑直接翻译，总之通顺准确即可。急需截止25号。... 请哪位高人帮忙找道这篇的中文：Preparation of Plasmid DNA by Alkaline Lysis with SDS: Minipreparation（题）或者帮忙翻译一下，要求不要用电脑直接翻译，总之通顺准确即可。急需截止25号。原文如下： 1. Inoculate 2 ml of rich medium (LB， YT， or Terrific Broth) containing the appropriate antibiotic with a single colony of transformed bacteria. Incubate the culture overnight at 37°C with vigorous shaking. 2. Pour 1.5 ml of the culture into a microfuge tube. Centrifuge at maximum speed for 30 seconds at 4°C in a microfuge. Store the unused portion of the original culture at 4°C. 3. Remove the medium by aspiration， leaving the bacterial pellet as dry as possible. 4. Resuspend the bacterial pellet in 100 μl of ice-cold Alkaline lysis solution I by vigorous vortexing. 5. Add 200 μl of freshly prepared Alkaline lysis solution II to each bacterial suspension. Close the tube tightly， and mix the contents by inverting the tube rapidly five times. Do not vortex! Store the tube on ice. 6. Add 150 μl of ice-cold Alkaline lysis solution III. Close the tube and disperse Alkaline lysis solution III through the viscous bacterial lysate by inverting the tube several times. Store the tube on ice for 3-5 minutes. 7. Centrifuge the bacterial lysate at maximum speed for 5 minutes at 4°C in a microfuge. Transfer the supernatant to a fresh tube. 8. (Optional) Add an equal volume of phenol:chloroform. Mix the organic and aqueous phases by vortexing and then centrifuge the emulsion at maximum speed for 2 minutes at 4°C in a microfuge. Transfer the aqueous upper layer to a fresh tube. 9. Precipitate nucleic acids from the supernatant by adding 2 volumes of ethanol at room temperature. Mix the solution by vortexing and then allow the mixture to stand for 2 minutes at room temperature. 10. Collect the precipitated nucleic acids by centrifugation at maximum speed for 5 minutes at 4°C in a microfuge. 11. Remove the supernatant by gentle aspiration as described in Step 3 above. Stand the tube in an inverted position on a paper towel to allow all of the fluid to drain away. Use a Kimwipe or disposable pipette tip to remove any drops of fluid adhering to the walls of the tube. 12. Add 1 ml of 70% ethanol to the pellet and invert the closed tube several times. Recover the DNA by centrifugation at maximum speed for 2 minutes at 4°C in a microfuge. 13. Remove all of the supernatant by gentle aspiration as described in Step 3.Take care with this step， as the pellet sometimes does not adhere tightly to the tube. 14. Remove any beads of ethanol that form on the sides of the tube. Store the open tube at room temperature until the ethanol has evaporated and no fluid is visible in the tube (5-10 minutes). 15. Dissolve the nucleic acids in 50 μl of TE (pH 8.0) containing 20 μg/ml DNase-free RNase A (pancreatic RNase). Vortex the solution gently for a few seconds. Store the DNA solution at -20°C. 展开

帮我翻译这段话，急需。有关石碱: 石碱，出山东济宁诸处。彼人采蒿蓼之属，开窖浸水，漉起，晒干烧灰，以原水淋汁，每百引入粉面二、三斤，久则凝淀如石，连汁货之四方，浣衣发面，甚获利也。他处以灶灰淋浓汁，亦去垢发面。

防火服的技术要求:

蒸汽发生器的技术要求是什么？: 蒸汽发生器的技术要求是什么？

国家有关血液冷藏箱的要求有哪些？: 国家有关血液冷藏箱的要求有哪些？

求翻译，与生物有关，不要机翻: AfterdissectioneachsamplewasplacedinamicrotubefilledwithNaClsolution(0.9%w/v)andwascarefullycrushedmechanicallyandasuspensionwaspreparedusingavibrationshaker.HPLC-diodear... After dissection each sample was placed in a microtube filled with NaCl solution (0.9% w/v) and was carefully crushed mechanically and a suspension was prepared using a vibration shaker. HPLC-diode array laminar flow cabinet. 展开