近来这段时间我店里的大型洗衣设备有些异常，该怎么检查和保养一下啊？

独醉雄起 2012-12-04 01:37:04 433 浏览

有时候觉得噪音有点大。... 有时候觉得噪音有点大。展开

参与评论

登录后参与评论

全部评论(6条)

Syh1598 2012-12-05 00:00:00

应该拿去维修部

赞(12)

回复(0)

评论

评论
登录后参与评论
jinsihui0819 2012-12-05 00:00:00

请公司售后进行保养

赞(10)

回复(0)

评论

评论
登录后参与评论
小帅59108 2012-12-06 00:00:00

应该找厂家的专业人士进行检查保养，自己检查保养不全

赞(18)

回复(0)

评论

评论
登录后参与评论
mingzou_007 2012-12-05 00:00:00

这种设备尽量请专业技术人员来检查维修。

赞(10)

回复(0)

评论

评论
登录后参与评论
yajun74316 2012-12-05 00:00:00

请专业维修的来检查一下。

赞(12)

回复(0)

评论

评论
登录后参与评论
panbus0y 2012-12-05 00:00:00

目前国内干洗店设备维护与保养不同程度地存在着许多问题，甚至不安全因素。为减少事故发生，使设备运行在Z佳状态，提高工作效率，上海川岛洗涤设备提醒用户注意一下几点，仅供参考。 1．检查皮带张紧力时，用拇指垂直于两皮带轮切线的中点，按压皮带，皮带内陷15-20mm为正常。 2．定期清理蒸汽管和水管上安装的过滤器，检查疏水阀工作是否正常。 3．定期清理自动烘干控制器。 4．溶剂泵工作情况下不应将钮扣收集篮提起，防止异物进入管道卡住油泵叶轮。 5．锅炉上水泵如停机超过一周再投入工作，应先将电机风扇叶松后再启动，以防堵转，烧坏电机。 6．电热式干洗机、小锅炉冷却后压力表度数应为零，如大于零应将炉内压力排掉。 7．每半年打开空气道，将附着在冷、热盘管、风扇叶轮和气流通道内的纤毛彻底清理，以提高烘干效率，减少污物对机器的腐蚀。 8．洗衣房内所有蒸汽管道保温材料完好，定期更换蒸汽软管，以减少热能损失和防止烫伤。 9．将压力表压力控制器、安全阀送有关部门核检，不合格必须更换同规格配件后才能投入运行。

赞(2)

回复(0)

评论

评论
登录后参与评论

登录或新用户注册

微信登录
密码登录
短信登录

请用手机微信扫描下方二维码
快速登录或注册新账号

微信扫码，手机电脑联动

注册登录即表示同意《仪器网服务条款》和《隐私协议》

热门问答

近来这段时间我店里的大型洗衣设备有些异常，该怎么检查和保养一下啊？: 有时候觉得噪音有点大。... 有时候觉得噪音有点大。展开

该怎么保养雾化喷嘴喷头啊？:

请问一下大型55KW分散机，设备容积达到多少啊？:

谁能帮我翻译一下这段英文文献啊: Fig. 1 shows that diamond particles are dispersed in the copper matrix. Since the diamond particles are easy to be stripped off during mechanical polishing， small pits are left on the surface of samples. When the samples were analyzed b... Fig. 1 shows that diamond particles are dispersed in the copper matrix. Since the diamond particles are easy to be stripped off during mechanical polishing， small pits are left on the surface of samples. When the samples were analyzed by electron probe for carbon， the particles displayed high carbon peaks， as shown in Fig. 2. Fig. 3 exhibits the analyzed result for extracted product of the copper–diamond composite by X-ray diffraction (XRD) analysis. It is shown that three dif- fraction peaks exist， shown as A， B and C， respectively. The interplanar distances corresponding to the three peaks and standard ones for diamond are compared in Table 1. The measured values of the interplanar distances are in good agreement with the standard ones， demon- strating that the extracted product should be the carbon in diamond state. Fig. 4(a) gives a TEM micrograph showing distribution and morphology of diamond particles (indicated as A， B， and C) in the copper–diamond composite. The calibration of interplanar distance for diffraction rings in Fig. 4(b) was given in Table 2. Compared to Table 1， it is also demon- strated that the calibrated interplanar distances for the diffraction rings conform to the standard ones of diamond. Therefore， it is believed that the graphitization of diamond particles hardly occurs after sintering at 1150–1220 K in the copper–diamond composite. Although diamond is a metastable allotropic modifica- tion of carbon， the graphitization of diamond particles in the copper–diamond composite did not occur， or the degree of graphitization was too small to be found. It is believed that the beginning temperature of graphi- tization would be associated with the purity of diamond powders. The impurities such as some metallic elements reduce the beginning temperature of diamond graphitiza- tion. When diamond is fabricated by the static synthesis method， Fe and Ni are often used as catalysts and are present in diamond as impurities to decrease the beginning temperature of graphitization [6]. It is understandable that both for the graphitization and its reverse reactions， their activation energies can be decreased by catalytic agents. Compared with the diamond fabricated by static synthesis， the diamond powders prepared by explosion method do not contain metallic impurities， thus leading to an obvious increase in the beginning temperature of graphitization. Hence， the detonation synthetic diamond might be more resistant to graphitization and probably suitable for the electric contact materials. 展开

我刚做完离子烫该怎么保养头发？: 我是一个男生，刚做好离子烫，头发要怎么保养，效果才可以持久？需要每一次洗完头后使用护发素吗？是不是还要使用发膜。还有，用什么牌子的护理产品比较好？

为什么这段时间网络卡: 以前好的，玩YY啊什么CF。DNF都不卡。但这1个月都很卡，电脑和猫1开就玩5分钟就开始卡了，而且我知道应该是网络卡和电脑没关系，应为电脑还算好电脑，那么为什么卡呢？？？高手救救我啊，每次玩游戏别人不卡，就我卡。。。。。。。。。。555555555555

请问一下我父亲因为白血病化疗，现在肝受到损伤，该怎么保养?: 有医生朋友么?我父亲因为急性非淋巴细胞白血病化疗了3次，之前一次几乎是从鬼门关回来的，现在休息了一个多月了，转氨酶高，应该是肝脏被损伤了，现在该在饮食，起居方面如何保养呢?谢谢拉!有什么东西是保肝的呢?

我店里同时卖高能磁化净水器和纯水机该怎么向客户介绍:

请问一下肛门内窥镜检查痔疮时一般检查时间有几分钟啊: 请问一下肛门内窥镜检查痔疮时一般检查时间有几分钟啊？？请问一下肛门内窥镜检查痔疮时一般检查时间有几分钟啊？

我的胃不好，该如何保养:

店里安装了视频监控，我想在家就可以看到店里的情况，该怎么做:

铅防护服该怎么保养:

实验室家具怎么样，该怎么保养:

Z近皮肤感觉好干啊，该怎么保养啊，推荐下拉: Z近老感觉皮肤很干，很紧，涂过油后一会还是觉得应该再涂一遍，请大家推荐下洗面奶，爽肤水，油给我拉，谢谢。

请翻译一下这段英文1，谢谢: Materials For the present study， the matrix was ABS supplied by Formosa Co. The reinforcements were polyacrylonitrile based high strength CFs. The properties of materials used were given in Table 1. Carbon fibre surface treatment Carbon fi... Materials For the present study， the matrix was ABS supplied by Formosa Co. The reinforcements were polyacrylonitrile based high strength CFs. The properties of materials used were given in Table 1. Carbon fibre surface treatment Carbon fibres were oxidised by boiling in HNO3 under reflux for 5 h (T5120uC). Afterwards， the nitric acid oxidised fibres were washed with distilled water to neutral pH. Fibre surface composition The fibres were characterised by X-ray photoelectron spectroscopy (ESCA 300， Scienta， Sweden) to determine the level of functionalisation of the modified fibres. An initial survey scan was performed to determine the detectable elements， followed by high resolution scans. The entire X-ray photoelectron spectrum was energy referenced to the C1s peak of graphite (bending energy5284?5 eV). Composite preparation Before processing， ABS pellets and CFs were dried in a vacuum oven for 4 h at 80uC. Composites containing 0， 5， 10， 15， 20， 25 and 30 wt-% SCF were prepared by melt mixing in a co-rotating twin screw extruder (Thermoprism TSE 16 TC， L/D:24). The ABS pellets and CFs were fed from the main and side feeders respectively. The molten composite obtained from the die of the extruder was water cooled and pelletised. The extrusion conditions were arranged， as shown in Table 2. The viscosity of the melt containing CFs depends on the viscosity of the polymer matrix as well as the processing temperature. To avoid unfavourable shearing conditions， the melt temperature is kept as high as possible regarding thermal degradation. Before PA6 was blended to promote interfacial adhesion， vacuum drying of the ABS and PA6 pellets was carried out at 80uC for 4 and 12 h respectively. The 0， 10， 20 and 30 wt-% PA6 containing batches were fed through the main feeder to the twin screw extruder. The extrudate was water cooled and chopped into small pellets. The produced ABS/PA6 pellets were vacuum dried again at 80uC for 12 h. To prepare the SCF reinforced ABS/PA6 composites， the blend was introduced into the twin screw extruder from the main feeder， and SCFs were fed from the side feeder. The twin screw extruder was operated at the same processing conditions used during the blend preparation. The extrudate was again water cooled and chopped into small pellets. The extrusion grades of resin were used to make the extrudate form fully. The specimens for the mechanical characterisation experiments were moulded using a laboratory scale injection moulding machine (microinjector， model 1998; Daca Instruments) at a barrel temperature of 230uC and mould temperature of 80uC. The injection moulding machine used in this study was a laboratory type microinjector. The principle of the operation is that the preweighed (，2?5 g) raw material is loaded into the cylindrical barrel and allowed to melt at a preset barrel temperature for 1 min.Then the molten plastic is pushed through an injection tip by a piston. 展开