钳形电流表精度±(3.0%+5)中，+5什么意思？

狮子鲁昭 2018-01-26 08:14:39 474 浏览

参与评论

登录后参与评论

全部评论(1条)

mixdulexs 2018-01-27 00:00:00

数字表的误差表示方法，误差比量程的3%还要多出“5”个末位字。例如3位半显示的200.0A的档位，误差可以达到200X3%+0.5=6.0+0.5=6.。

赞(1)

回复(0)

评论

评论
登录后参与评论

热门问答

钳形电流表精度±(3.0%+5)中，+5什么意思？:

全站仪精度±2″/5″ 什么意思 0.4？:

乳胶管5*9什么意思:

三相电流表500/5什么意思:

色度仪±5% 10 pcu什么意思:

电流表 6L2-A 250/5 中250/5是什么意思？:

汽车转速表，指针5表示什么意思？:

红外测温仪参数中的红外测温精度正负1. 5摄氏度是啥意思？:

pe等径三通dn90×5表示什么意思:

请问钳形表交直流电流精度±2.5%±5是什么意思？:

LED显示屏室内3.0单色 3.0什么意思:

钳形电流表的中a ac什么意思:

高分英译中 (5): CIPTankFill–theCIPtankisfilledfromoneoftheunitsinoperation.CIPTankHeating–foracidCIPs，thewaterintheCIPtankisheatedto40°C.Backwash-Theskidisbackwashedtoremoveexcesssoli... CIP Tank Fill – the CIP tank is filled from one of the units in operation. CIP Tank Heating – for acid CIPs， the water in the CIP tank is heated to 40 °C. Backwash - The skid is backwashed to remove excess solids and maximize the chemical cleaning efficiency. The backwash waste is drained to the regular waste outlet. Hot water Fill - The skid is filled with water from the CIP tank. Filtrate Recirculation and Chemical Dosing - The CIP transfer/recirculation pump starts to recirculate the water to the skid in a closed loop. The skid is fully isolated from the rest of the system， typically by block and bleed systems. The acid or chlorine (sodium hypochlorite) is added in the loop at the beginning of the recirculation sequence until the appropriate quantity of cleaning chemical is added. Filtrate Recirculation – The cleaning solution is recirculated through the filtrate side of the membrane array. This step is similar to filtration. Soak/Aeration - The modules are left to soak for a preset time. With an acid clean， repeated aeration steps can be used to improve cleaning efficiency. Draindown - The cleaning solution is drained away from the skid to drain or to the neutralization system if the system incorporates one. Rinse Backwash - The skid is refilled with feed water and backwashed to remove residual chemical. All rinse water is directed to drain or the neutralization system. Filtration to Waste – The unit is put into filtration but the filtrate with chemical residue is sent to drain or the neutralization system. The pH and ORP meters are used to verify that the skids have been rinsed to the point where the filtrate has no chemical cleaning residue. The unit can then be put back into filtration or standby. Pressure Decay Test (PDT) The integrity test procedure is similar to that used on all of the other Memcor systems. The principal process steps include draining down the lumen of the fibers， pressurizing the inside of the module fibers with integrity air while the upper backwash waste outlet valve is open to atmospheric pressure， shutting down the air supply and monitoring the pressure over time using the filtrate pressure transmitter supplied with each unit. The PDT result is logged on the SCADA system and displayed on the SCADA computer as well as the optional local HMI. This result is used to calculate the Log Removal Value (LRV)， which confirms integrity of the system. Each Memcor CP unit is tested at regular time interval adjustable by the operator. The time interval is set at 24 hours by default. 展开