上古卷轴5远古保护罩

则US方哈 2013-11-28 09:43:02 362 浏览

是在哪个任务里得到的啊~具体点吧

参与评论

登录后参与评论

全部评论(2条)

暮雨春色 2013-12-01 00:00:00

LS的说得十分正确，但是这个任务领取也是有条件的，那就是刺杀鹰眼团巡逻官的任务必须wan美达成，何谓wan美达成呢，那就是所有任务分支（可选择）都做到，这个任务就必须在主城里把目标杀死，黑精灵女刺客才会给你奥拉瓦标记。。

赞(6)

回复(0)

评论

评论
登录后参与评论
1019639113 2013-11-29 00:00:00

做兄弟会主线的任务，忘了是杀了皇帝的妹妹后给的还是杀了巡逻官后给的一个小任务任务是叫你去雪漫找一个老女人，一天到晚都坐在自己家门前那个，叫什么虚弱的什么那个女人会给你一个任务，去左上角的一个弃誓者的地方（打了前面进到里面还有，里面有一个古诺德的遗址，里面一群女巫）找一个远古兄弟会的会员是尸体他身上的装备就是了 PS：这装备听说可以和其他装备叠加，如： 0护甲的头部 + 有护甲的头部+ 远古保护罩本人就没用过。。。。

赞(4)

回复(0)

评论

评论
登录后参与评论

热门问答

上古卷轴5远古保护罩: 是在哪个任务里得到的啊~具体点吧

上古卷轴5夜视怎么用:

上古卷轴5夜视时间延长: 怎么将上古卷轴5夜视时间延长一下60秒太短了什么方法都行... 怎么将上古卷轴5夜视时间延长一下 60秒太短了什么方法都行展开

小白鼠一只，求上古卷轴5必备工具包~~~:

上古卷轴5洞察术和夜视都不好使了?: 我装了很多mod，洞察术和夜视也都能用，大概两天没玩，再玩的时候赶夜路发现夜视不好使了，用洞察术也不引路了，怎回事？补充一下，我上了以前的存档试了一下，发现洞察和夜视都还能用... 我装了很多mod，洞察术和夜视也都能用，大概两天没玩，再玩的时候赶夜路发现夜视不好使了，用洞察术也不引路了，怎回事？补充一下，我上了以前的存档试了一下，发现洞察和夜视都还能用，怎么回事？刚才又试了一下，发现连吸血鬼大君都不能变身了，崩溃。。。展开

核金弹头ol基因合成卷轴有什么用:

电风扇保护罩: 电风扇保护罩电风扇保护罩后半部分怎么装，掉下来了，装不回去！

保护罩英文:

联轴器保护罩: 图中圈出来的部件叫什么？装在电机端，联轴器外部。铝制的，这个东西仅仅是联轴器保护罩？有没有国家标准。

钳形电流表精度±(3.0%+5)中，+5什么意思？:

iphone6s音响保护罩:

高分英译中 (5): CIPTankFill–theCIPtankisfilledfromoneoftheunitsinoperation.CIPTankHeating–foracidCIPs，thewaterintheCIPtankisheatedto40°C.Backwash-Theskidisbackwashedtoremoveexcesssoli... CIP Tank Fill – the CIP tank is filled from one of the units in operation. CIP Tank Heating – for acid CIPs， the water in the CIP tank is heated to 40 °C. Backwash - The skid is backwashed to remove excess solids and maximize the chemical cleaning efficiency. The backwash waste is drained to the regular waste outlet. Hot water Fill - The skid is filled with water from the CIP tank. Filtrate Recirculation and Chemical Dosing - The CIP transfer/recirculation pump starts to recirculate the water to the skid in a closed loop. The skid is fully isolated from the rest of the system， typically by block and bleed systems. The acid or chlorine (sodium hypochlorite) is added in the loop at the beginning of the recirculation sequence until the appropriate quantity of cleaning chemical is added. Filtrate Recirculation – The cleaning solution is recirculated through the filtrate side of the membrane array. This step is similar to filtration. Soak/Aeration - The modules are left to soak for a preset time. With an acid clean， repeated aeration steps can be used to improve cleaning efficiency. Draindown - The cleaning solution is drained away from the skid to drain or to the neutralization system if the system incorporates one. Rinse Backwash - The skid is refilled with feed water and backwashed to remove residual chemical. All rinse water is directed to drain or the neutralization system. Filtration to Waste – The unit is put into filtration but the filtrate with chemical residue is sent to drain or the neutralization system. The pH and ORP meters are used to verify that the skids have been rinsed to the point where the filtrate has no chemical cleaning residue. The unit can then be put back into filtration or standby. Pressure Decay Test (PDT) The integrity test procedure is similar to that used on all of the other Memcor systems. The principal process steps include draining down the lumen of the fibers， pressurizing the inside of the module fibers with integrity air while the upper backwash waste outlet valve is open to atmospheric pressure， shutting down the air supply and monitoring the pressure over time using the filtrate pressure transmitter supplied with each unit. The PDT result is logged on the SCADA system and displayed on the SCADA computer as well as the optional local HMI. This result is used to calculate the Log Removal Value (LRV)， which confirms integrity of the system. Each Memcor CP unit is tested at regular time interval adjustable by the operator. The time interval is set at 24 hours by default. 展开

pm2. 5衡量标准:

5月突出贡献榜

推荐主页

上古卷轴5远古保护罩

联系我们

关注我们